電動執行器調試安裝使用說明
！注意事項 For Your Safety
! 請仔細閱讀本注意事項,，避免帶來的受傷或更嚴重事故 !
For better and safety use for a long period, please observe this warning and caution carefully
告 警告 Warning
本產品非防爆型,，請勿使用于易燃易爆環境下,，或腐蝕氣體中
This product is not of explosion-proof. Do not use it in the environment with flammable
gas (gasoline etc.) or corrosive gas.
請勿帶電從閥門上拆除執行器
Do not dismantle the actuator from the valve during power operation
請勿通電時接線工作
Do not do wiring work when power is being supplied
心 小心 Caution
本產品是電器產品,，如野蠻敲砸或摔落,，易導致失效
Do not drop the product or give a shock to the product, for it may cause defects to the
product
請勿在雨中或有水飛濺的環境中接線
概述 General:
本系列產品是高質量回轉型電動執行機構,， 用于控制回轉閥門的開關及運動到所需位置,。
This serial product is a high performance quarter-turn rotary type electric valve actuator for
on/off and intermediate position service.
特點 Feature:
緊湊輕巧 Compact and light
切斷電源后,，可通過附帶的手柄進行手動操作 Manual operation by crank handle available
電機內置熱保護 Thermal protection from motor burn-out
防水等級 IP67 Water proof to IP 67
ISO5211 接口便于安裝 ISO5211 mounting
9  10
注意： 本線路圖僅供參考，實際以產品附帶電路圖為準
Note: This wiring diagram is only for reference. Please follow the diagram adhere on the product.
接線線路圖 Wiring Diagram
普通開關型  無源開關信號
智能調節型  直流開關型
無源開關信號
智能調節型  直流開關型
三相無源觸點型  三相開關型
性能參數 Performance Parameter
型號 Model
較大輸出扭矩
Max. Torque
(N.M)
動作時間
90°(S) Run-
ning Time
(s)
運行角度
Rotate
Angle
電機
(W)
motor
額定電流
(Cur) 220V
(A)50HZ
重量
（Kg)
Weight
FLOWX-005  50  20  0~360°  10  0.16  2
FLOWX-010  100  30  0~360°  25  0.35  3
FLOWX-020  200  30  0~90°  40  0.37  8
FLOWX-040  400  30  0~90°  90  0.57  8.5
FLOWX-060  600  45  0~90°  90  0.6  9
FLOWX-100  1000  30  0~90°  120  0.94  17
FLOWX-160  1600  48  0~90°  140  0.96  17
FLOWX-250  2500  75  0~90°  140  0.98  18
標準技術參數 Common technical data
電機電源 Power supply 110V AC, 220V AC, 380V AC, 24V DC
電機 Motor 鼠籠式異步電機 Squirrel-cage Asynchronous type
防護等級 Waterproof IP67
電氣接口 Conduit M20*1.5
環境溫度 Ambient Temp. -20 ℃ - +60 ℃
選裝功能 Option 除濕加熱器 heater
外涂層 External coating 環氧樹脂 Epoxy polyester
11
安裝 Installation
1.  安裝注意 Caution of installation
本產品屬非防爆產品,，請注意避開易燃,，易爆等環境
This product is not of explosion-proof type. Do not install in hazardous place.
在雨水、原料等飛濺物和陽光直射的環境,，需安裝保護電動執行機構的防護裝置
Need a protective cover if it is installed in a water or material splashing area or
direct sunlight area.
請預留接線,、手動操作等安裝維修空間
Please reserve a space for manual maintenance.
2.  環境溫度和工作介質溫度 Ambient and Fluid temperature
2.1 環境溫度 Ambient temperature
周邊環境溫度-30℃ ~60℃范圍內 Ambient temp: -30℃~60℃
環境溫度在零度以下時，可選裝除濕加熱器
For use in minus temp, in-fit space heater is available at option
2.2 工作介質溫度 Fluid Temperature
與閥門配套使用時,，介質的熱量會傳到機體上面,，執行機構溫度會升高
If the actuator is applied to a high temp fluid application, the unit may overheat
by transmission of heat.
介質溫度65 度以下時，選用標準支架或免支架
Standard bracket: fluid temp max. 65℃
介質溫度65 度以上時,，選用高溫支架
Radiation type bracket: fluid temp over 65℃
3.  現場電纜線安裝要求 Cable Requirement
用外徑Ø9~11的電纜,如圖1,不能使
用與防水接頭內徑不相適應的電纜,，否
則水可以從防水接頭進入執行機構內損
壞內部零件
Using a cable of Ø9~11 for the
standard connector. If a customer con-
nector is used, select a proper diame-
ter to prevent water ingress to the unit
圖1