微機滾動摩擦磨損試驗機該機還可以做潤滑劑的長時抗磨損試驗，測定摩擦系數,，記錄摩擦力和溫度曲線,。該機可選配高精度測量裝置，可實現摩擦副摩斑的計算屏幕顯示,，測量和記錄,。使用特殊附件，也可以進行端面摩損和材料的模擬試驗,。

微機滾動摩擦磨損試驗機產品優勢： （1）試驗完畢后,，可以隨意設定并獲?。耗硶r(shí)間段內的試驗數據 （2）曲線顯示：時間—溫度、時間—摩擦系數,、溫度—摩擦系數,、轉速—溫度等 （3）可以設定采集頻率，按照設定的采集頻率獲取試驗數據并導出到EXCEL （4）可以把試驗數據和試驗曲線導出電子版,，使試驗數據與試驗曲線結合,，便于存檔和打印 （5）儀器傳動機構由步進電極升級為交流伺服電機，轉速精密可調,，更加穩定可靠,，轉矩大，噪音小 （6）設置有封閉式砝碼加載裝置和摩擦試驗更加安全可靠,，透明視窗可觀察摩擦狀態 （7）轉速可調,，可自由設置試驗速度 （8）打印報告參數可選，可以根據需要自行選擇要打印的實驗參數 （9）10N.M量程傳感器與精密伺服電機配合,，可以實現大負荷試驗需求 （10）外觀采用人工學曲線設計,，外形美觀，簡潔大方 （11）新增加實時溫度采集功能,，可以滿足在不同摩擦溫度下的試驗數據 （12）配有油液槽,，可以在油液里進行測試

?

技術參數Technical parameters：  M-200

1、試樣尺寸： 30mm×7mm×6mm,； sample size: 30mm x 7mm x 6mm;

2,、轉動速度rotation speed： ≤200 轉/分（可調adjustable）；

3,、負荷load： (20KG)196N ± 0.1%,可增至(40KG)392N,；

4、摩擦環尺寸：≥￠40×10mm ,，倒角≥0.5×45°,，外圓表面與內圓同心度偏差≤0.01；the size of the friction ring is greater than or equal to 40 x 10mm, the chamfering is equal to 0.5 x 45 degrees, and the concentricity deviation between the outer surface and the inner circle is less than 0.01.

5,、摩擦環材質：45 號鋼,；friction ring material: No. 45 steel;

6、摩擦力矩： 0—4N.m,；friction torque: 0 - 4N.m;

7,、砝碼重量：4KG 砝碼十件，1KG 砝碼十件,，可實現重量疊加功能,；weight weight: 4KG weight ten, 1KG weight ten, can achieve weight superposition function.

8、精度：速度精度≤1%,；負荷精度≤0.5%,；摩擦力矩精度≤1%,；計數器精度≤1S；傳感器測量精度≤1%F,。accuracy: speed accuracy is less than 1%; load accuracy is less than 0.5%; friction torque accuracy is less than 1%; counter accuracy is less than 1S; sensor measurement accuracy is less than 1%F.

9,、配件parts：

試驗主機一臺；Test host one;

高精度扭矩傳感器一只,；High precision torque sensor one;

計算機數據采集卡一塊,；A piece of computer data acquisition card;

計算機控制系統一套；A set of computer control systems;

標準摩擦環二件,；Two standard friction rings;

使用說明書一份,；One copy of the instructions;

產品合格證一份；A copy of the product certificate;

產品裝箱單一份,。A single copy of the packing of the products

 ?

試驗設備test equipment

1,、傳動系統，用來帶動圓環以給定的轉速旋轉,，精確到5%以內,，并要求圓環安裝部位軸的徑向跳動小于0.01毫米。1. The transmission system is used to drive the ring to rotate at a given speed, accurate to within 5%, and the radial runout of the shaft at the installation position of the ring is required to be less than 0.01mm.

2,、加載系統,，對試樣和圓環，可施加法向力,，精確到5%以內,。2. Loading system, for the sample and the ring, the additional force can be applied, accurate to within 5%.

3、測定和記錄摩擦力矩系統,，精確到5%以內,。3. Measure and record the friction torque system to within 5%.

4、記錄圓環轉數的計數器或記時器,，精確到1%以內,。4. A counter or chronograph for recording the revolution of a ring, with an accuracy of less than 1%.

5,、試樣夾具結構和尺寸見圖2,，并附配墊圈 4 GB 848-76，沉頭螺釘M3×0.35長10毫米,。要保證試樣安置后無軸向竄動,。5. See Fig. 2 for the structure and dimension of the sample clamp, with washer 4 GB 848-76, countersunk screw m3 × 0.35 with length of 10 mm. Ensure that there is no axial movement after the sample is placed.

注：試驗設備本標準推薦采用M-200型磨損試驗機。Note: M-200 wear testing machine is recommended in this standard.

6,、本試驗中圓環的材質對塑料磨損試驗結果影響很大,，因此本標準采用的圓環，其外形尺寸見圖3,。6. The material of the ring in this test has a great influence on the plastic wear test results. Therefore, the ring adopted in this standard has the dimensions shown in Figure 3.

材料為45號鋼,，圓環要求整體淬火,，熱處理HRC 40～45，外圓表面光潔度▽8,，倒角處均為0.5×45度,，外圓表面與內圓同心度偏差小于0.01.The material is 45 steel, the ring is required to be quenched as a whole, the heat treatment is HRC 40-45, the surface finish of the outer circle is ▽ 8, the chamfering is 0.5 × 45 degree, and the concentricity deviation between the outer circle surface and the inner circle is less than 0.01.

    圓環可以反復使用，每次試驗后,，需重新磨削,。當外徑小于36毫米就不能再用。作仲裁試驗時必須用直徑40毫米的圓環,。The ring can be used repeatedly. After each test, it needs to be grinded again. When the outer diameter is less than 36 mm, it can not be reused. A ring with a diameter of 40 mm must be used for the arbitration test.

注：圓環材質也可按產品標準另定,。Note: the ring material can also be determined according to the product standard.

適用范圍及功能 符合標準：GB/ T 3960-2017 塑料滑動摩擦磨損試驗方法 GB/T 9141.8-1999 柔性石墨板材滑動摩擦系數測試方法 適用于塑料制品、橡膠制品,、石墨板材或其他復合材料的滑動摩擦,，磨損性能測試，也可對試驗中試樣的磨擦力,、磨擦系數和磨損量進行測定,。 本儀器融合了當前的智能電路系統進行控制，并結合老式M-200摩擦磨損試驗機的功能進行升級改造而成,，本儀器具有測控精度高,，操作便捷等優勢，是科研院所,、質檢機構,、實驗室研究的試驗設備。 M-200型摩擦磨損試驗機主要由試驗主機及智能控制系統兩大部分構成,，通過微機控制系統進行操作試驗,，在試驗過程中同時可以顯示數值、扭矩,、時間曲線,，并可以隨意設定試驗次數，顯示當前試驗數值,，設定時間及當前試驗時間等多種功能,，隨機配備彩色打印機，可以打印出帶有曲線,、表格數據等標準要求的試驗報告,。

?