日韩av大片在线观看欧美成人不卡|午夜先锋看片|中国女人18毛片水多|免费xx高潮喷水|国产大片美女av|丰满老熟妇好大bbbbbbbbbbb|人妻上司四区|japanese人妻少妇乱中文|少妇做爰喷水高潮受不了|美女人妻被颜射的视频,亚洲国产精品久久艾草一,俄罗斯6一一11萝裸体自慰,午夜三级理论在线观看无码

一,、滑觸線斷電
A sliding contact line power,
主要原因：電刷在導管中爬坡,；電刷磨損嚴重，無法觸及導體,；導體接頭不平整,；單集電器使用；導軌接頭松脫,。
The main reason: brush in the conduit climbing; brush wear serious, can not touch the conductor; the conductor joint roughness; single collector; rail joint loosening.
處理方法：檢測集電器是否磨損嚴重,，更換集電器；更換電刷,；重新調整連接節點,；采用雙刷集電器；重新調整擰緊連接螺釘,。
Treatment methods: detection of collector is badly worn, replace the collector; Replacement Brush; re adjust the connection; with double brush collector; re adjust, tighten the screw connection.
二,、導軌變形,，集電器運動受阻
Two, rail deformation, collector movement blocked
主要原因：環境溫度過高,；提掛架間距大或松脫。
The main reason: the high ambient temperature; lifting rack spacing or loose.
處理方法：局部采用隔熱板,，室外加遮陽板,；增加滑觸線提掛架數量，矯正導管,，并擰緊螺釘,。
Processing method: partial use of insulation board, outdoor and visor; increase the sliding contact wire rack number provided, correct catheter, and tighten the screws.
三、工作時滑觸線晃動大
Three, work of sliding contact line shaking big
主要原因：撥叉無法吸收傳動誤差,；導軌正線直線度差,；提掛架松動。
The main reason: fork cannot absorb transmission error; rail line straightness deviation; lifting rack loose.
處理方法：修正牽引器,，使之能自由吸收傳動誤差,；調整導軌直線度；擰緊提掛架螺釘,。
Treatment methods: fixed traction device, which can free free absorption, transmission error; the adjusting guide rail straightness; tighten screws lifting rack.
四,、電刷磨損快
Four, brush wear quickly
主要原因：接頭不平整；載流量過大,；彈簧壓力大,。
The main reason: joint roughness; carrying capacity is too large; the spring pressure.
處理方法：按要求重新連接導軌,；增加集電器數量；更換,、修正彈簧壓力,。
Processing method: according to the requirement of re connected with the guide rail; increase the collector number; replacement, correction spring pressure.
五、電刷側面擦傷
Five, brush side abrasion
主要原因：電刷磨損,，滑觸線集電器定為不正,；牽引器的撥叉?zhèn)攘鬟f過大。
The main reason: brush wear, sliding touch line collector for it; the shifting fork side force of the tractor transmission is too large.
處理方法：更換,、修正彈簧壓力,；更換牽引撥叉或修正牽引器撥叉。
Processing method: replacement, correction spring pressure; replace the traction fork or modified tractor fork.
六,、導軌內有火花
Six, rail spark
主要原因：電刷表面與導軌接觸不良,。
The main reason: brush the surface in contact with the rail side.
處理方法：檢測導軌接頭，適當磨合電刷保證60%接觸面積,。
Treatment methods: detecting the rail joint, appropriate running in brush to ensure 60% contact area.
七,、滑觸線集電器行走有較大異響
Seven, the sliding contact line collector walking has large abnormal sound
主要原因：電流過大；接頭不平整,。
The main reason: the current is too large; joint roughness.
處理方法：增加集電器數量,；重新安裝導軌連接。
Treatment methods: increase the collector number; re install rail connection.
八,、滑觸線集電器外殼擦傷
Eight, the sliding contact line collector casing abrasion
主要原因：導軌變形,；集電器定為欠佳。
The main reason: rail deformation; collector for the poor.
處理方法：按故障2處理,，增加定型夾,；調整集電器。
Processing method: according to the fault treatment increased 2, shaping clamp; adjust the collector.