1、本試驗箱體采用鋁合金框架＋電解板靜電噴涂,，具有外觀美觀,、防銹防腐等特點
2、箱體頂部設有強力抽風排煙系統,，在試驗完成時,，與送風系統同時打開，能將廢氣排出到室外,；試驗過程中,，此系統為封閉狀態。
3、箱體后側面設有送風門,。在試驗完成時,，抽風系統打開時，向箱內送風,，試驗過程中,，此封閉需關閉。（提供,；全部換完空氣所需的時間值）
4,、箱體正面設有試驗過程中可以密封的鋼化玻璃觀察窗，便于觀察試驗情況,。
5,、在玻璃觀察窗下方開有一個可以將手和胳膊伸到試驗箱的進行操作的孔，此孔裝有密封手套,，操作者利用密封手套進行操作燃燒噴燈,，配備密封手套一雙。
6,、試驗箱體規格：220X130X165（CM）,，容積：4.8m³

1, the test box with aluminum alloy frame + electrolytic plate electrostatic spraying, with beautiful appearance, rust prevention and corrosion characteristics
2, the top of the box is equipped with a powerful exhaust system, when the test is completed, and the air supply system can be opened at the same time, the exhaust gas can be discharged to the outdoor.
3, the rear side of the box is equipped with air door. When the test is completed, the draft system is turned on, and the air is supplied to the box. To provide the time needed for all the air to be changed
4, the front of the box with the test process can be sealed glass window, easy to observe the test situation.
In 5, below the glass window to open a hole can be operated hand and arm out of the test box, the hole is provided with a sealing glove, the operator of the sealing gloves for operating combustion burner, equipped with a pair of gloves sealed.
6, test case specification: 220X130X165 (CM), volume: 4.8m fand

上海今森燃燒試驗儀UL1581測溫系統：

1、熱傳感器（銅制導管和熱電偶）—導管結構應為傳導率*的電解銅（提供相應電解銅的密度）,。長度為19.14±0.02mm,；（另附送一個不裝熱電偶的感溫銅頭一個）

2、K型熱電耦,，配0.5mm直徑的不銹鋼管做外套,。
3、智能PID溫控表和K型熱電耦相匹配,。其讀數可大1000℃,。
4、整過測試系統為：活動式,，測溫時將其置于試驗箱內,，進行測溫。配備測溫裝置一套,。
5,、配備電子秒表：精確到0.1S（在測溫校驗時備用）

1, thermal sensor (copper tube and thermocouple) - the structure of the catheter should be very high conductivity of electrolytic copper (to provide the appropriate density of electrolytic copper). Length of 19.14 + 0.02mm; (also attached to a thermocouple does not install a temperature sensitive copper head)
2, K type thermoelectric coupling, with 0.5mm diameter stainless steel pipe to make coats.
3, inligent PID temperature control meter and K type thermoelectric coupling. The reading can be 1000.
4, the whole test system is: active type, temperature will be placed in the test chamber, temperature measurement. Equipped with a set of temperature measurement device.
5, equipped with electronic stopwatch: accurate to 0.1S (in the temperature check standby)

上海今森燃燒試驗儀UL1581試驗裝置及試驗夾具

1、主要夾具：試驗支架與燃燒噴燈
2,、試驗支架：由不銹鋼制作,，分水平支架與垂直支架獨立式，即FT1,、FT2,、VW-1三種規格。垂直支架與噴燈所在平面與觀察窗平面平行，便于觀察與操作,。
3,、燃燒噴燈：滿足ASTM D5025-99要求，標準功率：垂直噴燈為500W,，水平噴燈為225W,，噴火口直徑：0.90±0.03mm，噴口燈長度：1.60±0.05mm,，噴口距空氣進口高度為102mm,；噴燈角度：水平為90度，垂直為20度（縱向軸線保持在垂直平面上且與垂直方向產生20°的夾角）
4,、楔形架：增加楔子,，噴燈安要求安裝在楔子上，并能方便移動,，同時能精確移回到規定位置,。
5、配備可以測量水平和垂直燃燒時內,、外焰的標尺一套,。
6、配備500MM精確到1MM的鋼尺一把,，以備試驗用,。

1, the main test fixture: bracket and combustion burner
2, test support: made of stainless steel, sub level and vertical support stand independent, that is, FT1, FT2, VW-1 three specifications. The vertical bracket and the blowtorch plane and the plane parallel observation window, convenient observation and operation.
3, combustion burner: power to meet the ASTM standard requirements: D5025-99, vertical 500W level for the torch torch, 225W, crater diameter: 0.90 + 0.03mm, 1.60 + 0.05mm lamp nozzle length, nozzle distance of air inlet height 102mm; burner angle: level of 90 degrees, 20 degrees vertical (longitudinal axis is maintained at an angle in the vertical plane and vertical direction of 20 degrees)
4, wedge support: increasing the security requirements of wedges, burner installed on a wedge, and is convenient to move, and move back to the specified position accuray.
5, can be equipped with measuring horizontal and vertical burning, a ruler in the outer flame.
6, equipped with 500MM accurate to 1MM steel to test for.

燃?xì)饧霸囼?yàn)耗材 

1、燃?xì)猓杭淄椋兌?8%以上,，要由供應商憑證書證明）,，熱值998BTU（英國熱量單位）/立方英尺。每立方米37.1兆焦耳,。（自備）
2,、脫脂棉花與牛皮紙(自備)

1, gas: methane (purity of more than 98%, to be certified by the supplier certificate), calorific value 998BTU (British thermal unit) / cubic feet. 37 trillion and 100 billion joules per cubic meter. (own)
2, cotton and kraft paper (owned)

流量控制系統：

1、主要包括：流量計,、減壓閥,、背壓力管均采用美國DWYER公司原裝，型號分別為：RMA-13-SSV100-1000cc/min）,、62030MU(0-200Kpa)、1230-36-D（0~36”w.c.）
2,、流量計：流量量程1000ml/min
3,、燃燒減壓閥：1個，可將氣體流量調節器至10磅/立方英寸
4,、背壓力管：水柱高度精度到5mm或以下
5,、背壓力液體：為紅油
6、可選配美國APBUCK公司的流量校準儀：規格：1CC/min~6000CC/min（對玻璃轉子流量計進行校準用）（價格另計） n>、楔形架：增加楔子,，噴燈安要求安裝在楔子上,，并能方便移動，同時能精確移回到規定位置,。
5,、配備可以測量水平和垂直燃燒時內、外焰的標尺一套,。
6,、配備500MM精確到1MM的鋼尺一把，以備試驗用,。

1, including: flow meter, pressure relief valve, back pressure pipe are used in the United States DWYER company original, models are: RMA-13-SSV100-1000cc/min), 62030MU (0-200Kpa), 1230-36-D (0~36) W.C.)
2, flowmeter: flow range 1000ml/min
3, combustion valve: 1, the gas flow regulator to 10 pounds / cubic inch
4, back pressure pipe: water column height accuracy to 5mm or below
5, the back pressure of the liquid to Chili oil
6, flow calibration instrument matching the United States APBUCK company: specification: 1CC/min~6000CC/min (on the glass rotameter calibrated by (n>) price plus), wedge support: increasing the security requirements of wedges, burner installed on a wedge, and is convenient to move, and move back to the specified position accuray.
5, can be equipped with measuring horizontal and vertical burning, a ruler in the outer flame.
6, equipped with 500MM accurate to 1MM steel to test for.

計時系統與燃燒次數累計系統本試驗裝置提供燃燒次數,、燃燒計時、持燃燒計時與延燃計時三個計時系統,，三個計時器的功能如下：
1,、 燃燒計時：當燃燒著了的噴燈到達規定位置時，自動記錄噴火時間（按規定設定：如燃燒15S）,，試驗員通過觀察所設定的時間,，當噴火時間到達瞬間，手很快轉動楔形架,，移開噴燈,。
2、 持燃計時：當上述燃燒計時到達后,，此計時器自動計時,；如果在規定時間（如：停止供火15S），此過程中,，如果被燃燒的樣品火焰熄滅,，那么再進行第二次燃燒，重復*步燃燒過程,。
3,、 延燃計時：如果在上一步規定時間內，未熄滅,，用腳踏啟動另一個延燃燒計時器,，如在規定延燃時間內熄滅，接著重復進行*步燃燒試驗,，若在規定時間內未能熄滅,，直接判定試驗失敗。
4,、 能自動記錄燃燒次數,，以免造成失誤,；
5、 并設有相應的蜂鳴報警聲,。

1, the combustion timing: when burning the torch at the specified position, automatically record the flame time (according to the provisions set: such as the burning of 15S), the test personnel by observing the set time, when the time arrived at the moment of fire, hand quickly turned away a wedge frame.
2, the burning time: when the combustion time arrives, the timer timing automatically; if within the specified time (such as: fire stop for 15S), in this process, if the sample is burning flame extinguished, then second times of combustion, repeat the first step in the combustion process.
3, burning time: if not extinguished in a specified time step, and start another extension of the combustion timer use the pedal, such as burning time out in the regulations, then repeat the first step of combustion test, if within the specified time to go out, directly determine the test failure.
4, can automatically record the number of combustion, so as not to cause mistakes;
5, and with the corresponding beep alarm sound.